C O N T R O L L E D
M O T I O N   I N C .
       ~ INTELLIGENT FLUID POWER ~
   ~ INTELLIGENT FLUID POWER ~
We offer Tie Rod, Welded Body and Telescopic Hydraulic Cylinders and Replacement Parts for Miller, Parker, Prince and Chief.  
Contact us today for a quote!
Photo Album Gallery Place Holder - Please wait while the Photo Album loads. If the album does not show, please refresh the page to try again.

Hydraulic cylinders (also called linear hydraulic motors) are mechanical actuators that are used to give a linear force through a linear stroke. A hydraulic cylinder is without doubt the best known hydraulic component. Hydraulic cylinders are able to give pushing and pulling forces of millions of metric tons, with only a simple hydraulic system. Very simple hydraulic cylinders are used in presses; here the cylinder consists out of a volume in a piece of iron with a plunger pushed in it and sealed with a cover. By pumping hydraulic fluid in the volume, the plunger is pushed out with a force of plunger-area * pressure.

More sophisticated cylinders have a body with end cover, a piston-rod with piston and a cylinder-head. At one side the bottom is for instance connected to a single clevis, whereas at the other side, the piston rod also is foreseen with a single clevis. The cylinder shell normally has hydraulic connections at both sides. A connection at bottom side and one at cylinder head side. If oil is pushed under the piston, the piston-rod is pushed out and oil that was between the piston and the cylinder head is pushed back to the oil-tank again.

Simple hydraulic cylinders have a maximum working pressure of about 70 bar, the next step is 140 bar, 210 bar, 320/350 bar and further, the cylinders are in general custom build. The stroke of a hydraulic cylinder is limited by the manufacturing process. The majority of hydraulic cylinders have a stroke between 0,3 and 5 metres, whereas 12-15 metre stroke is also possible, but for this length only a limited number of suppliers are on the market.

In case the retracted length of the cylinder is too long for the cylinder to be build in the structure. In this case telescopic cylinders can be used. One has to realize that for simple pushing applications telescopic cylinders might be available easily; for higher forces and/or double acting cylinders, they must be designed especially and are very expensive. If hydraulic cylinders are only used for pushing and the piston rod is brought in again by other means, one can also use plunger cylinders. Plunger cylinders have no sealing over the piston, or the piston does not exist. This means that only one oil connection is necessary. In general the diameter of the plunger is rather large compared with a normal piston cylinder, because this large area is needed.

Whereas a hydraulic motor will always leak oil, a hydraulic cylinder does not have a leakage over the piston nor over the cylinder head sealing, so that there is no need for a mechanical brake.

Tie Rod Style Hydraulic Cylinders use high strength threaded steel rods to hold the two end caps to the cylinder barrel. This method of construction is most often seen in industrial factory applications. Small bore cylinders usually have 4 tie rods, while large bore cylinders may require as many as 16 or 20 tie rods in order to retain the end caps under the tremendous forces produced. Tie rod style cylinders can be completely disassembled for service and repair.

The National Fluid Power Association (NFPA) has standardized the dimensions of hydraulic tie rod cylinders. This enables cylinders from different manufacturers to interchange within the same mountings.

Welded Body Cylinders have no tie rods. The barrel is welded directly to the end caps. The ports are welded to the barrel. The front rod gland is usually threaded into or bolted to the cylinder barrel. This allows the piston rod assembly and the rod seals to be removed for service.

Welded body cylinders have a number of advantages over tie rod style cylinders. They have a narrower body and often a shorter overall length enabling them to fit better into the tight confines of machinery. Welded cylinders do not suffer from failure due to tie rod stretch at high pressures and long strokes. The welded design also lends itself to customization. Special features are easily added to the cylinder body. These may include special ports, custom mounts, valve manifolds, and so on.

The smooth outer body of welded cylinders also enables the design of multi-stage telescopic cylinders.

Welded body hydraulic cylinders dominate the mobile hydraulic equipment market such as construction equipment (bulldozers, excavators and road graders) and material handling equipment (fork lift trucks, telehandlers, and lift gates). They are also used in heavy industry such as cranes, oil rigs, and large off road vehicles in above ground mining.
Telescopic Cylinder

The length of a hydraulic cylinder is the total of the stroke, the thickness of the piston, the thickness of bottom and head and the length of the connections. Often this length does not fit in the machine. In that case the piston rod is also used as a piston barrel and a second piston rod is used. These kind of cylinders are called telescopic cylincers. If we call a normal rod cylinder single stage, telescopic cylinders are multi-stage units of two, three, four, five and even six stages. In general telescopic cylinders are much more expensive than normal cylinders. Most telescopic cylinders are single acting (push). Double acting telescopic cylincers must be specially designed and manufactured.